CodeWarrior for HCS12 V4.7 BDM调试时为什么总和TARGET板连不上

昊天

不知道什么原因，BDM调试时 驱动也装好了，ＴＢＤＭＬ的参数也设定好了，可是就是烧不上程序，在ｃｏｍａｎｄ　ｗｉｎｄｏｗ　显示
executing C_layout.hwl
!OPEN source 0 0 60 39
NO CONNECTION
!Source < attributes TOOLTIP on,TOOLTIP_FORMAT signed,TOOLTIP_MODE details,FREEZE off,MARKS off
!OPEN assembly 60 0 40 31
!Assembly < attributes ADR on,CODE off,ABSADR on,SYMB off,FORMAT Auto,FREEZE off,TOPPC 0x0
!OPEN procedure 0 39 60 17
!Procedure < attributes VALUES on,TYPES off
!OPEN register 60 31 40 25
!Register < attributes FORMAT AUTO,COMPLEMENT None
!OPEN memory 60 56 40 22
!Memory < attributes FORMAT hex,COMPLEMENT None,WORD 1,ASC on,ADR on,MODE automatic,UPDATERATE 10,ADDRESS 0x0
!OPEN data 0 56 60 22
!Data:1 < attributes SCOPE global,COMPLEMENT None,FORMAT Symb,MODE automatic,SORT NotSort,UPDATERATE 10,NAMEWIDTH 16
!OPEN data 0 78 60 22
!Data:2 < attributes SCOPE local,COMPLEMENT None,FORMAT Symb,MODE automatic,SORT NotSort,UPDATERATE 10,NAMEWIDTH 16
!OPEN command 60 78 40 22
!Command < attributes CACHESIZE 1000
!bckcolor 50331647
!font 'Courier New' 9 BLACK
!AUTOSIZE on
!ACTIVATE "Data:2" "Command" "Procedure" "Data:1" "Register" "Assembly" "Memory" "Source"
done C_layout.hwl

Communication settings:
SETCOMM COMPORT LPT "TBDML #1"
Initializing STARTUP command file:
CMDFILE STARTUP ON ".\cmd\TBDML_startup.cmd"
Initializing RESET command file:
CMDFILE RESET ON ".\cmd\TBDML_reset.cmd"
Initializing PRELOAD command file:
CMDFILE PRELOAD ON ".\cmd\TBDML_preload.cmd"
Initializing POSTLOAD command file:
CMDFILE POSTLOAD ON ".\cmd\TBDML_postload.cmd"
GDI:   DiDirectAddMenuItem()==> DI_OK
GDI:   DiGdiInitIO()==> DI_ERR_FATAL
Initializing STARTUP command file:
CMDFILE STARTUP ON ".\cmd\TBDML_startup.cmd"
Initializing RESET command file:
CMDFILE RESET ON ".\cmd\TBDML_reset.cmd"
Initializing PRELOAD command file:
CMDFILE PRELOAD ON ".\cmd\TBDML_preload.cmd"
Initializing POSTLOAD command file:
CMDFILE POSTLOAD ON ".\cmd\TBDML_postload.cmd"
GDI:   DiDirectAddMenuItem()==> DI_OK
GDI:   DiDirectAddMenuItem()==> DI_OK
No Link To Target
in>

whut_wj

<>这种问题没有遇到过,你用的那种BDM?</P><P>&nbsp;</P>

yudongx

重新复位一下芯片

yzst

我也这样啊

1233211234567

查查调试器的插头和目标板上的插针各个脚是不是对应连接的

whut_wj

检查供电和接线。

棉花糖9062

插头换一个方向。我们也有这个问题。换一下BDM的方向就好了。